#30 AMP 220 PLUG INSTALL#

You can plug a 30-amp RV cableĭirectly into a 50-amp power outlet, such as a power outlet or pedestal at any campground that offers them. Some people worry that the extra power that is supplied by a 50-amp outlet will fry their Recreational Vehicle's electrical system. Yes! You can plug your 30-Amp RV Cord into a 50-Amp Power Pedestal. Do not forget this step.Ĭan I Plug My 30-Amp RV Cord into a 50-Amp Power Pedestal? Be sure to secure the wires that inside the 30 amp RV plug. Tighten up the small straps that are located on the cord's cover jacket at the top.If there is no green screw then connect the ground wire to the U-shaped pin. The ground wire is bare green and should be connected to the green-colored screw.

The white neutral wire should be placed where the The hot wire is black and should be connected to the screw that is brass-colored.

Follow correct wire color codes and be sure to link each cable correctly.

Try your best not to damage the brass pins when you draw them from their housing.

Twist the strands so that you will have a rope-like thread that is much more stronger than strands that have not been

Next, using a wire stripper, remove 1/2 inch of insulation from each of the 3 wires.

Try your best not to damage any of the insulation that covers each Leave a total of one inch to separate the 3 wires.

Use a box cutter carefully to cut the outer portion of of your cord's jacket cover.

Any rips made while pulling these wires will require a redo.įollow these steps to wire your 30 amp serviceįollow these steps in order to safely wire your 30 amp rv service. The wires slowly in order to avoid any rips. If you have never pulled any type of cable in the past, I suggest pulling

#30 AMP 220 PLUG INSTALL#

With all the materials on-hand, it is now time to install all the new wire you had laying around or the ones you might have purchased between the 30-amp outlet and the breaker. Be sure to double check the 10 gauge wire before you install it.

To safely wire a 30 amp service, you will need a wire gauge of 10. A cover plate for your outlet (Protect against the elements).Brand new breaker (Recommended to use a new breaker).You just learned what a 30 amp rv service is, now we will go over all the materials that are needed to complete the job. Things you will need to wire your 30 amp rv service Wiring a 30 amp rv service is straightforward, and can be easily done by following the correct color codes for your connections and by using the proper wire size or sizes. Reveals a U-shaped pin and two flat pins that are angled. The 30-amp Recreational Vehicle plug is usually referred to as the RV-30. In the Rv world, a 30-amp power service is defined as an outlet that offers 120 volts and outputs power through a three-prong male cable and a 30-amp breaker. Visit Article Close What is a 30 amp rv service? Would you like to read another article on 50 amp wire size? And even if they were, they don't need to be.just make them all with the heaviest gauge and be done with it.Hey, i noticed that you are enjoying this article so far. The stupidity of this is that, as far as I can see, the actual terminals of a 220 volt 30 amp plug are no heavier gauge than a 480 volt 20 amp plug. This is a constant annoyance for those of us using 'used' plugs from various machines, where they practically never match up and one gets to grace the local electrical supply house with another 30 bucks for a plug that ought to cost 5 bucks.

Now, as if that wasn't ridiculous enough, there are 220 volts 20 amps, 220 volts 30 amps.and on and on.Īnd then there are plugs with an extra ground wire in the middle ! A different plug configuration for every conceivable voltage and amperage combination ? There are plugs for 220 volts, 250 volts, 120/250 volts, 440 volts and 480 volts.

30 amp 220 plug